Wencon UW Cream
Wencon UW Cream is a two component cream, to be applied on wet surfaces or under water. The UW Cream is excellent for filling up holes, dents and rebuilding of surfaces which, due to high humidity, has to be done in wet conditions.
Typical applications are corroded hulls and all underwater parts of ships and structures, tanks, pipes, flange faces, etc. It is also excellent for filling up cavitation damages on hulls and rudders.
After curing Wencon UW Cream is resistant to oil, saltwater, water, most diluted acids and a range of solvents.
- Can be applied on wet surfaces or under water
- Cures under water and on wet surfaces
- For filling up cavitation damages
- Long pot-life under water
- Strong adhesion to all metal and GRE surfaces
| Key technical data |
| Max temperature | +60- +160°C (140 - 320° F) |
| Consistency | paste |
| Mixing ratio vol. | 1:2 |
| Apply with | spatula |
| Potlife at 20°C | 25-35 min. mixed in small amounts |
| Curing time | 10-18 hours |
| Machineability | yes |
| Specific volume | 526 cm3 / kg |
| Dielectric strength | 10 KV/mm |
| Product number | Product name | IMPA no. | ISSA no. |
| No. 1014 | Wencon UW Cream, 0,5 kg (1,1lb) unit | 812334 | 75.553.91 |
Wencon UW Cream is a two-component compound to be applied on wet surfaces or under water. The UW Cream is excellent for filling up holes, dents and rebuilding of surfaces which, due to high humidity, have to be done in wet conditions.
After curing Wencon UW Cream will show many of the same characteristics of metal, together with outstanding adhesion to all metallic surfaces, this makes the compound highly suitable for repair and rebuilding corroded and worn metal surfaces.
Wencon UW Cream is non-conductive and will therefore not cause bi-metallic corrosion. After curing Wencon UW Cream is resistant to oil, salt water, water, most diluted acids and a range of solvents.
APPLICATION AREAS
Typical applications are corroded hulls and all underwater parts of ships and structures, tanks, pipes, flange faces, etc. Wencon UW Cream is also suitable for filling up cavitation damages on hulls and rudders.
MIXING
Wencon UW Cream has to be mixed above water in the mixing ratio 1:2 by volume.
GENERAL DESCRIPTION
Two-component solvent free pasty consistency epoxy repair compound, for applying under water or on wet surfaces.
SURFACE PREPARATION
Before applying, the surface must be clean from loose paint, scales, under water growth, etc. A mechanical cleaning will do, but even better, if possible, hydro jetting.
MIXING RATIO
Mix by volume 1:2. Mix until an even color is obtained. The mixing has to take place above water. After mixing, the product can be taken into the water.
POT LIFE
Depending on amount mixed and the temperature. Mixed in small amounts, the pot life is approximately 25-35 minutes at 20°C (68°F)
APPLYING
Wencon UW Cream is applied using the spat- ula supplied with the kit.
In order to ensure close contact, be sure to work the product well into the surface to be treated.
CURING TIME
Curing will take place in 10-18 hours, but only if the temperature allows it to cure. Curing requires a temperature of at least 10˚C (50˚F), but better at 17-23°C (62-73°F) or higher.
If the coating shall be exposed to chemicals, let it cure for 7 days before exposure.
REDUCED CURING TIME WITH INFRARED
This product is tested with and suitable for infrared curing. Curing with infrared radiation can reduce curing time significantly. Result can vary, depending on circumstances and equipment used.
MACHINABLE
After curing, the product can be machined, drilled and worked like metal.
TECHNICAL DATA
Hardness Shore D: 79 (DIN 53505)
Tensile strength: 35,8 N/mm² - 5094 p.s.i. (DIN 53454)
Compressive strength:
Modulus of elasticity: 2631 N/mm² - 375,000 p.s.i. (DIN 53454)
Rcrack: 134 N/mm² -19,000 p.s.i. (DIN 53454)
Shear adhesion: 33 N/mm² - (ASTM D1002)
Adhesion to steel: 7,5 N/mm² - (ISO 4624)
SPECIFIC VOLUME
526 cm³ per kilogram (32,1 cu inch/kg)
TEMPERATURE RESISTANCE
Corrosion and heavy load: 60°C (140°F)
Light load or no load: 100°C (212°F)
As filler: 160°C (320°F)
CHEMICAL RESISTANCE
The compound is resistant to oil, water, salt water and most diluted acids and alkalis as well as a range of solvents.
SHELF LIFE
At 20°C (68°F) : 3 years
HANDLING PRECAUTIONS
Read the Wencon Instruction for Use and the Material Safety Data Sheet.
| Бренд | WENCON |
|---|---|
| Product Name | Wencon UW Cream |
ООО «Бастини»
Мы можем предложить широкий выбор оборудования, материалов и запасных частей в соответствии с высокими требованиями к качеству.
Bastini предлагает каждому клиенту услуги, адаптированные к его конкретным потребностям, исходя из нашего опыта поставок.
Bastini - надежный поставщик промышленных товаров и оборудования для обеспечения безопасности.
Наш ассортимент всегда обновляется и адаптируется к требованиям наших покупателей.
Все ваши запросы будут обработаны с максимальным вниманием и в короткие сроки.
Заказы будут упакованы и доставлены в кратчайшие сроки и отправлены в любую точку мира.
Наша компания известна как поставщик решений в цепочке поставок оборудования и логистике.
Адрес офиса 195279, Санкт-Петербург шоссе Революции, дом 69, лит.В, вход 2, офис 16
Телефоны: +7 (812) 458-35-97 ; +7 (921) 380-77-97
Email: office@bastini.ru